I read the ski date card proxmark3. I tried to upload data to Chameleon Ultra via GUI. The program does not provide such an opportunity. How to upload card 15693 data to the chameleon in order to emulate it from the chameleon?
I don’t think the Chameleon supports iso15693?
1 Like
Doesn’t even emulate?
that would fall under the definition of not supporting.
1 Like
I don’t understand why?
With what can I emulate iso 15693? I can’t find a map for a clone with 66 blocks…
[usb] pm3 → hf 15 info
[=] Using scan mode
[=] — Tag Information ---------------------------
[+] UID… E0 16 3C 66 13 2C 6B FF
[+] TYPE… EM-Marin SA (Skidata); EM4237 [IC id = 15] 23,5pF
[+] SYSINFO… 00 0F FF 6B 2C 13 66 3C 16 E0 02 00 41 03 0F
[+] DSFID… 0x02
[+] AFI… 0x00
[+] IC ref… 0x0F
[+] Tag memory layout (vendor dependent)
[+] 4 ( or 3 ) bytes/blocks x 66 blocks
[+] 264 total bytes
Because nobody wrote the software for the chameleon to do that yet.
the iceman firmware
You could submit a support request maybe 
Do you have a Proxmark?
@Aoxhwjfoavdlhsvfpzha did i mention how helpful your PM3 emulator tool is???
2 Likes
I downloaded this card into Prokhmark’s memory [usb] pm3 → hf 15 eload -f hf-15-E0163C66132C6BFF-dump.bin
[+] loaded 2235 bytes from binary file hf-15-E0163C66132C6BFF-dump.bin
[=] Clearing emulator memory
[=] Uploading to emulator memory
[=] …
[+] uploaded 2235 bytes to emulator memory
[?] You are ready to simulate. See hf 15 sim -h
[=] Done!
[usb] pm3 → hf 15 esave -f hf-15-E0163C66132C6BFF-dump.bin
[=] Downloading 2235 bytes from emulator memory
[+] saved 2235 bytes to binary file /Users/maximzhukov/hf-15-E0163C66132C6BFF-dump-002.bin
[+] saved to json file /Users/maximzhukov/hf-15-E0163C66132C6BFF-dump.bin.json
[usb] pm3 → hf 15 eview
[=] Downloading 2235 bytes from emulator memory…
Now my question is, can I emulate this card with Proxmark 3 memory without a laptop, using battery power? If this is possible, then how to do it?
the proxmark3 easy does not have a battery or the extended flash mem to store this credential. so no.
you could modify the proxmark to add SPI flash & make a standalone for doing the emulation but it is currently not set up to do it.
you can use an android phone, OTG cable & the termux app (more info on the Proxmark Repo) to use your proxmark 3 easy portably
Correct, I just gave that as an alternative for you to consider.
As @Equipter said above would be the easiest way with a PM3
There are other Proxmark options that might be worth investigating.
A cheaper of those options would be a Proxmark3-X
It has Bluetooth and a battery.
You could achive the same as above with Termux but via Bluetooth, so nop cables and more discreet if that is what you are after…
I can’t confirm the following will work, But if you were to plug in a powerbank to the side port of the PM3 Easy, you would have power, and Standalone mode MIGHT allow ISO15963 emulation, or plug it into a laptop, start emulating, remove from laptop ( whilst still powered via a powerbank )
Just some more things for you to consider
Just some more things for you to consider
What should I pay attention to?
Friends, I thank you for your answers! Thank you and low regards!
I don’t want to be intrusive. But the question arose by itself))
Are there magic ISO 15693 cards that change the UID to 66 blocks of 2235 bytes? To make a clone of my card.
[usb] pm3 → hf 15 info
[=] Using scan mode
[=] — Tag Information ---------------------------
[+] UID… E0 16 3C 66 13 2C 6B FF
[+] TYPE… EM-Marin SA (Skidata); EM4237 [IC id = 15] 23,5pF
[+] SYSINFO… 00 0F FF 6B 2C 13 66 3C 16 E0 02 00 41 03 0F
[+] DSFID… 0x02
[+] AFI… 0x00
[+] IC ref… 0x0F
[+] Tag memory layout (vendor dependent)
[+] 4 ( or 3 ) bytes/blocks x 66 blocks
[+] 264 total bytes
If such exist, where can I buy it?
Probably, lost in translation
What I meant was, you have other options.
examples that I gave you