not a bad thought
I assumed a one stop shop was what you were after
And whilst I agree
I agree with this 
more
WHAAATTTTT ???
I FUCKEN LOVE IT
2 Likes
its pretty. it has a well designed UI. but there is a lot of eye searching to grab the content needed. For front of house info i think it is perfect.
3 Likes
Good recovery 
2 Likes
Not sure if this is still being updated but wanted to add that the Flipper Zero is compatible with the NExT (T5577). I successfully cloned a HIDProx generic RFID badge to my implant using the Flipper Zero and tested the implant in the real world - worked perfectly. Placement of the zero is a bit tricky while programming of course. Found that it helps to put it in constant ASK read mode and then figure out the best orientation. Then leaving the flipper in place on your hand where it read the best, switch to write mode and write what you wish. Guessing since the NExT works, any other T5577 based chips would as well.
Just noticed that the spreadsheet didn’t say YES for the NExT (T5577) but did for the NExT (NTAG216) so I wanted to git it updated if possible since it works great for both.
2 Likes
Cheers buddy, I do neex to do an update around Flipper, and add a few more compatiable implants
Apologies if this is in the wrong category. Bought this nfc door lock off Amazon and wanted to share. $55 confirmed working with xmagic.
Limited-time deal: ENOKER Smart keyless Entry Door Lock 5 in 1 Fingerprint Door Knob Lock with APP/IC Key Cards/Passcode/Backup Keys/ 100 Fingerprints with Keypad Handle for Home Hotel Office Apartment Bedroom Amazon.com
3 Likes
It might be worth writing a review of that lock: Reviews - Dangerous Things Forum
Also, @Pilgrimsmaster, there’s a new lock for the matrix.
3 Likes
Not at all,
All good and easily moved.
Thanks for taking the time to share
Cheers buddy, I’ll do that SOON ™
3 Likes
Thank you, I’ll be sure to do that.
Some things on my mind…
- Apex Flex works with ACR1252 (New - need to add)
- Apex Flex and xM1 works with DL533R (New - need to add)
- Apex Flex works with KBR1
- NExT (125kHz) works with DMP 7073 (New - need to add)
- NExT (125kHz) works with P-300-H-A (New - need to add)
- KBR1 doesn’t read my xSLX
- xMagic is now released, will need a link, and be moved to the appropriate categories
- flexSecure needs to be added and needs a link
- flexClass needs to be added and needs a link.
- flexClass works with PM3 Easy
- I think…I read that the xBT works with Flipper Zero
- Apex Flex needs a link.
1 Like
Heavy burden
Consider it lifted, I will do some updates
Including this Cheers
4 Likes
I just saw this in my drafts
Might as well post it, even though I did it nearly 2 months ago
- Apex Flex works with ACR1252 (New - need to add) DONE
- Apex Flex and xM1 works with DL533R (New - need to add) DONE
- Apex Flex works with KBR1 DONE
- NExT (125kHz) works with DMP 7073 (New - need to add) DONE
- NExT (125kHz) works with P-300-H-A (New - need to add) DONE
- KBR1 doesn’t read my xSLX DONE
- xMagic is now released, will need a link, and be moved to the appropriate categories DONE
- flexSecure needs to be added and needs a link DONE
- flexClass needs to be added and needs a link.DONE
- flexClass works with PM3 Easy DONE
- I think…I read that the xBT works with Flipper Zero DONE
- Apex Flex needs a link. DONE
5 Likes
"TMEZON Smart Door Lock Fingerprint, Keyless Entry Door Lock with Handle, APP/IC Cards/Codes/Keys/Fingerprints Biometric Electronic Keyless Entry Lock for Bedroom Home Hotel Office "
Works with xMagic and Apex Flex. Though it reads the xMagic easier than the Apex surprisingly. Very small crappy reader in it, have an RSP on it and it barely works. With the 2.1L MFGC it reads like a charm.
The “Smart Lock” tags it comes with pull up as “Mifare Classic 1k”
Additionally, NiMH AAA batteries work just fine in it even though it says not to use them. Just shows up as ~64% charged when full.
3 Likes
I just bought an Aqara u50 and can confirm that it does NOT work with an NeXt implant.
4 Likes
A couple printers/copiers I wanted to add:
- RICOH MP C4503 - We had one at my old workplace that worked with my NExT after I cloned my LF HID (H10301) work badge to it.
- Brother MFC-L6900DW - Works well with my Magic ring v2 as well as my FlexUG4. My NExT “kind of” works but it is extremely hard to get it to read. It triggers based on UID alone so most cards should work. I can do more extensive testing with all my other cards if anyone wants.
Edit: Here is the Web interface for adding cards to the Brother MFC-L6900DW
5 Likes