FYI- flipperzeros are available right now for the USA

Lounge
41

Did you happen to use my guide?

If so, and since it was a recent for you: was it easy to follow? Did I miss anything? Does anything need updating?

42

I did use your guide. And had several others pulled up as well at the same time.

There were a few things.
Iā€™ll look at it tonight.

But I remember they had just said to update to the new firmware. And you needed to navigate in the files to where it said update inside the folder(I was looking for an exe file.)
Seems there was a few other things.

But if I can follow it pretty much anyone can Iā€™d think.

Iā€™ll have a look at the process and see if anything jumps out.

Thanks a ton for taking the time to write it. And update it. Hugely appreciated

1 Like
43

Hi, some feedback,

I didnā€™t find TheWholePackageOfEveryThingEver
I donā€™t think itā€™s on there anymore? At least not anywhere I could find. Hopefully Iā€™m not missing out on cool stuff, haha.

The short youtube video would actually have been helpful. I didnā€™t use it cause I thought it was a how to use it after the other part was done thingā€¦ I kind of struggled with the initial process, I think I downloaded something and was trying to figure out how to do the initial update on the flipper, but eventually figured it out. That would have made it even easier.
Cause here it just says download qflipper, but then doesnā€™t say what to do with it. And then moves on to installing the aftermarket firmwareā€¦
https://flipper.pingywon.com/

I do see now where it says to find update in the update folder, so that was my bad!

oh, and I just found the wholepackageofeverythingeverywhere!!!
I didnā€™t get to that part, i guess, I got right into trying to figure out how to copy to/from my bracelet, haha.
But itā€™s here, if this link is better for numbskullz like myself.
https://flipper.pingywon.com/flipper/zips/

I did it on the PC so did this method, to load the aftermarket firmware
From Flipper desktop (main screen) Press DOWN
then LEFT for ā€œbrowserā€
scroll DOWN and choose ā€œupdateā€ folder.
Scroll and run the ā€œupdateā€ from that dir.

Itā€™s good I had that because I was flailing around trying to figure out how to get there. lol.

all in all it was pretty easy. Iā€™m realizing I didnā€™t finish the process, haha.
Iā€™ll have to revisit it. I had about 5 tutorials all open and was going between them.

Iā€™d like to get an app/game of some kind on there just so I can say itā€™s not a micro machine to take over the world if someone asks me, hahahahahha (evil laugh).

Again, much appreciated, your time and patience and help with it.

Thanks for all you do!

1 Like
44

This https://flipper.pingywon.com/ website looks very shady to me.

45

Anything in particular?

Nothing stood out to me.

Just a some dude that put together all the Flipperstuff in one place :man_shrugging:

46

I updated the firmware, played around for a bit, then loaded Xtreme and was exploring that when I ended up hereā€¦

Flipped
Flipped1920Ɨ2560 191 KB

No combination of key presses seems to dislodge it.
Any ideas on how to get out of here?!

47

Have you tried DFU mode? Itā€™s for the stock firmware but presumably Xtreme left that in as a safety measure:

But first, try doing the following:

  1. Unplug the USB cable from your Flipper Zero if connected
  2. Press and hold the OK and BACK buttons for 30 seconds. It is normal if your Flipper Zero has no indications on the screen.
  3. Connect your Flipper Zero to a computer via a USB cable. The computer should detect your Flipper Zero as a DFU device.
1 Like
48
1 Like
49

Thank you both for the support. Rebooted and it all seems to be working fine now. :rat:

2 Likes