No laws against implants. It’s sort of a gray area. Not all piercers are capable of doing it just due to skill or openness to such a rad thing!
1 Like
Thanks! I’ll reach out when I have my kit!!
1 Like
Hey there, I believe I’m still on the map in Ft Lauderdale but have since relocated to Maryland to open and work the Studio by Painful Pleasures for ab 4-5 yrs. I’ll be back in Baltimore soon where I’ll be available for appointments if you’d like…
-I started piercing in 1992
-Met Amal at his first APP conference in Las Vegas where he expo’d the first NFC tags to the piercers there. What Year was that Amal?
2 Likes
That very well could be, the years of going to vegas for conference becomes diff to say which year what happened. But is xNT in me so I’d put 5 on it.
I’ve actually left my shop in Leesburg and will be down in Fredericksburg!
Please shoot me a message via IG if you’re wanting to get an implant done!
@dominionbodypiercing
So far I’ve done 6 and I think they’re rad! Keep em coming
3 Likes
He buddy, no problem advertising your piercing shop/ business here.
It’ll make it easy for people to find you.
Also, not everybody has instagram
Add as much detail as possible.
Name:
Shop Name:
Website:
email:
Phone number:
Social media:
We’ll also add you to a couple of community maps if your happy.
What sort of installs would you be happy with, and what locations?
Have you sern the range of implants available?
xSeries
are the glass capsules of varying, but similar sizes.
Bio Magnets
2 different form factors here
Flex
a coulple of variants in this
- The smaller “wafers”
~28mm x ~7.5mm
~38mm x ~8mm
- The larger FlexDisc
30mm diameter
For further info on implants
for further info on install locations
Some further info on implanting techniques ( you probably don’t need them, but there may be some little nuggets in there
Watch Installation procedure Guide 1
Watch Installation Procedure Guide 2
Watch Needle insertion angle
3 Likes
I’m able to install the pill chips and flex.
Not able due to current health codes do the magnet installs.
If it can be done with a needle/plunger needle I can do it in according to Virginia health law!
Please shoot me a message on IG or an email and we can arrange days I’m available to get em taken care of!
Thanks again
Mike
3 Likes
Do you happen to have a link to the installer list?
I’d like to promote doing more installs.
Currently have an apprentice under me at the shop and would love the chance to show her how to properly do installs on injectable and the flat wafer chips!
Appreciate ya!
Thank you!!
How can i go about being added to the DT map?
I’ve sent you a DM 
Just wanted to say that @DBP has done a flex and xSeries install for me. He’s professional, friendly, and is a good communicator. Both installs have healed well. Thanks again Mike!
3 Likes
Appreciate your trust and business! Looking forward to more installs
3 Likes
I’m in Ohio and may be coming your way in a few months. I am commenting in part to keep track of this and make sure I can find it later. Ohio is shit and no one can install anything here. 
1 Like
When you’re ready just shoot me an email! You can find me on the map now!
I’m in the shop sun/Mon/tues
2 Likes
Mega hyped. <3
You could use the bookmark function, located here
You can set a reminder
If you select 
None Needed, you can find that under your profile bookmarks, like such
Alternatively OR additionally, you can track the thread
(Located at the bottom of the thread)
or change the tracking settings
I appreciate the suggestions. Doing any of those would require remembering I did them. Writing it out helps me remember. And more different forums have a ‘see your own posts’ function than a bookmark function. It’s like telling someone to remind you to do something because then you won’t forget you told them. I apparently do get responses when someone replies to me, but that requires someone else to do something.
Like I’m willing to also try that. But I know what works for me as a general rule.
1 Like